10 ton oil fired steam boiler for textile industry
Since 2017, located in Changchun City, Jilin Province to accelerate the governance of coal-fired boilers within the city out of small coal-fired boilers remediation process. Up to now, the work has achieved initial success.
15 in the city with 20 kilowatts and above the coal-fired generating units, 13 units have ultra-low emissions; city table 292 with 20 t steam / hour or more coal-fired boilers, emission standards have reached the count 253 male , accounting for 86.64% of the proportion of the boiler with; the city built area of 10 steam tons / hour small coal-fired boilers 2962 units, out of a total of 29553 units, up 99.7% out of proportion, the basic completion of the national requirements out of the task.
In order to further improve air quality, improve people's living environment standards index, Changchun City by expanding the ban on burning area, improve the standard phase-out of coal-fired boilers, plans to use two years of urban 20 tons of steam / h coal-fired boiler (kiln) furnace eliminated.
By the end of 2017, the city has eliminated 20 tons of steam / hour coal-fired boilers 964 units; at the same time to speed up the central heating and (expanding) network as well as the pace of clean energy promotion, provide for the transformation of the city's coal-fired boiler control a strong guarantee.
In recent years, Changchun City, adhere to the full implementation of coal-fired boilers governance, to improve ambient air quality in Changchun City has played a positive role. 2017, good days Changchun 276 days, compared with 2013, an increase of 35 days; heavy pollution days 10 days compared to 2013, reduced by 33 days; major air pollutants respirable particulate matter (PM10) and fine particles (of PM2.5) were 78 mg / m and 46 micrograms / cubic meter, respectively, 39.5% and 37.0% decrease over 2013.
Use should pay attention to the problem of 10 ton fired steam boiler for textile industry pressure gauge. Rated steam pressure of less than 2.45MPa steam boiler, a manometer accuracy no less than 2.5; equal to the rated boiler steam pressure 2.45MPa, the pressure is not less than 1.5. Dial gauge diameter of not less than 100 mm, to ensure that the operator can clearly see the surface pressure indication. 2. Steam boiler gauge plate should draw a red line that indicates the maximum allowable working pressure. 3. The steam boiler pressure gauge should be installed in place to facilitate the observation and purged, and should prevent high temperature, vibration and icing. 4. The steam boiler pressure gauge should be checked at least once every six months, after calibration seal should be sealed. 5. The steam boiler gauge connection tube not leak water and steam, otherwise it will reduce the pressure instruction value. Biomass boiler is a kind of boiler to biomass energy as a boiler fuel called biomass boilers, steam boilers into biomass, biomass hot water boiler, biomass stove, biomass thermal oil heaters, vertical raw biomass boilers, biomass boilers and other horizontal. Steam boiler is an energy conversion device, the energy input to the boiler fuel chemical energy, electrical energy, thermal energy and other forms of high temperature flue gas, and after converting the boiler, the steam output having a certain outside thermal energy, high-temperature hot water or an organic carrier. 6. A steam boiler pressure gauge measuring range should be compatible with the operating pressure of the device under test, the working pressure is generally 1.53 times, preferably 2 times the working pressure. Steam boiler no pressure gauge, pressure gauge or pressure gauge damage does not meet the requirements. When the steam boiler pressure gauge of the following circumstances, should stop using: 1, the surface of the glass broken or blurred dial; 2, lead-free seal, lead seal is broken or exceeds the calibration cycle; 3. When no pressure gauge pointer position is limited to the limit staple nail can not be restored, and the unlimited gauge pointer from zero rank bit data is out of range pressure layer. Difference; 4, leak or pointer jump table; 5, other defects affect the gauge accuracy.
What are the technical parameters of the gas boiler boiler parameters are: 1, boiler capacity, which is the output Q, units of 10 ton fired steam boiler for textile industrys are tons / hour representation. Hot water boiler for heat MW / h represents; 2, pressure P, the unit is Mpa; 3, steam (or superheated steam) Temperature q, in degrees Centigrade. Hot water boiler expressed in terms of outlet temperature and return water temperature. Another area of the heating surface of each grate area, fuel type, fuel consumption, water temperature, total drag, with the wind (the wind drums) the amount of exhaust gas temperature and the like. The expression model are: the number of drum (e.g., single drum D, S, double drum); drum arrangement (transverse type H, the Z vertical type); combustion (chain L, G stationary grate etc.); a fuel type (coal a, gas Q, Y fuel, etc.); a steam boiler is usually "tons / h" or "t / h" is the capacity of the boiler. With "Mpa" or "MPa" (old unit of "kgf / cm 2" or "kgf / cm2") of the rated pressure of the boiler, it represents the temperature at the rated pressure saturated steam and superheated by "deg.] C" (Celsius) steam temperature. Thermal Efficiency Heat Transfer Fluid is a boiler furnace or a thermal transfer process, heat is absorbed by water, steam or thermal oil, accounting for complete combustion of the fuel into the boiler heat released percentage capacity of 1t / h steam boiler, i.e. It indicates that the boiler may be over 1 hour into water of 1 ton capacity of saturated steam under pressure; 0.7MW of such water heaters and furnaces heat Transfer Fluid representations may generate heat corresponding to 0.7MW power over 1 hour ( equivalent to one ton of steam heat). Two water boiler is the heating means for the hot water boiler working fluid. Usually "MW" (MW), with the old unit "when Wan kW /" or "million kcal / h", namely "104kcal / h" is the capacity of the boiler, with "Mpa" represents the rated pressure of the boiler, with "℃" the hot water temperature.
The capacity of the boiler is also called the output of the boiler. It is the basic characteristic parameter of the boiler. The 10 ton fired steam boiler for textile industry is expressed by the evaporation amount, and the common unit is ton/hour (t/h). Hot water boilers are expressed in terms of heat, in megawatts (MW). The hot water boiler produces 0.7 MW of heat, which is roughly equivalent to that of a steam boiler producing 1 t/h of steam. ZG boiler produces oil and gas boilers with different capacities, which indicate the rated output of the boiler, that is, the evaporation or heat supply under normal working conditions when the boiler is in continuous operation for a long time.