factory directly industrial thermal oil heater boiler
Since more than six months since the factory directly industrial thermal heater boiler equipment, heating and hot water supply well, our technical staff also view real-time remote monitoring and control through the use of the boiler to the scene, Baiyun Quan Lake hotel management staff related to our technical staff gave very great encouragement and affirmation. --customer feedback
Fuel gas-fired factory directly industrial thermal heater boiler installation steps Many users in the purchase of fuel gas-fired boiler fuel gas-fired boiler installation step is not clear, here we introduce to you in detail under the fast sale of shares by Henan side: We all know that the installation of the boiler is in line with national needs promulgated regulations to execute the regulations GB50273-98 "industrial boiler installation engineering construction and acceptance", but we should also note the following in the installation of several points: 1, the first part of the underlying foundation of compacted dust do, then start concreting and tiling, to try to make level, the maximum error of boiler placed inclination of not higher than 5mm, anterior need to open up a sewage tank. 2, the oil pipeline supply line is installed through the boiler plant, a senior technical staff installed a boiler factory is to have a portable installation instructions. 3, the combustor burner installed in the supply line the same as the factory mounted directly on the boiler, so this does not require the installation site 4, piping, valves, meters, accessories mounted fast due Henan local production of fuel gas boiler packaged boiler, so these are also in the factory have been installed, but because these instruments are not precision instruments collision, it will affect its accuracy, it is necessary to gently, the installation process must be careful. More questions about the installation of fuel gas-fired boiler, please contact customer service online!
Burner and flue installation and electrical installation and the fuel supply system of the burner 1, burner 1) before installation read "burner manual", according to the installation requirements. 2) Burner mounting flange, the middle requirements, to ensure the burner to the factory directly industrial thermal heater boiler flue gas does not leak at the interface. 2, the installation of fuel supply system (see schematic) Note: To prevent a fire caused by generation of static electricity in the fuel tank, the tank should have a good grounding. 1) supply system tank top tank top-feed system suction recommended distance between the back plane and the tubing inside diameter of the oil pump axis, the total length of the suction pipe Hm, m, no greater than DL6-34DL40-75DL100-250Di = 10mmDi = 14mmDi = 16mm0.51.03030401.535452.03535452.540503.0404050 Notes: (1) when there is an elbow or valve on the suction pipe, each of the length of the suction pipe to be minus 0.25m. (2) Di recommended internal diameter suction pipe and return pipe. 2) the distance between the bottom of the tank bottom of the tank supply system supply system pipe inner diameter recommended oil pump axis and a plane, the total length of the suction pipe Hm, m, no greater than DL6-34DL40-75DL100-250Di = 10mmDi = 14mmDi = 16mm1.03030401.535452.03535452.540503.04040504.045 Notes: (1) when there is an elbow or valve on the suction pipe, each of the length of the suction pipe to be minus 0.25m. (2) Di recommended internal diameter suction pipe and return pipe. 3, gas pipe installation requirements Burner gas line itself has been connected, the intake port, the intake pipe bends should be minimized and good sealing performance requirements, to prevent leakage. (Iv) a chimney installation, to prevent leakage, the leakage of smoke, to prevent smoke inhalation chamber. 2, a vertical mounting, a right angle bend bends should be avoided. 3, the top of the chimney must be water-resistant measures. (E) mounting a power switch with electrical connection box 1, the power switch should be considered easy to operate, away from heat, fixation, meet the design requirements. 2, the use of 220V (380V), 50HZ power source, and a ground line. 3, voltage instability in the region use, should be safe regulators. Or affect the normal operation of the combustion engine. 4, the power cord to the electrical box must be connected in strict accordance with the requirements, otherwise, there will be dangerous!
How fuel (gas) factory directly industrial thermal heater boiler stack height standards should be implemented as specified?According to requirements "Boiler Air Pollutants Emission Standard" -GB13271-2014 existing files countries, oil, gas boiler chimney of not less than 8 meters, the height of the boiler chimney by specific approval of environmental impact assessment documents OK. When there is a building within a radius of 200m from the new boiler room around the chimney, the chimney should be higher than the tallest building in more than 3m.