heavy oil hot water boiler in latvia
Oil hot water boiler in latvia configuration instructions show the advantages and features brought fuel for the boiler hot water boiler, the following, mainly through its specifically addressed several specific aspects of the talks, to continue to lead us to understand this kind of boiler, thus to increase the amount of knowledge that we respect. Therefore, we should take seriously and carry on, so in order to grasp and not waste such a good learning opportunity. 1. fuel hot water boiler, which is on display configuration, generally speaking, you can use what? And on which parameters can be set? Hot water boiler fuel, which is arranged on a display, in general, can use a dedicated microcomputer control of the boiler, and large-screen liquid crystal panel, thereby to clearly display, so that users can visually see the operation of the boiler status. Further, in the parameter setting, the work with a burner, boiler water temperature, water level, operation time, temperature and circulating pump turns off temperature, so that, for intuitive understanding, in order to determine the normal range within the allowable parameters . 2. fuel hot water boiler, which is structurally, is what are the characteristics that can bring some advantages? Features hot water boiler fuel in terms of structural design, and, it can bring some advantages, which mainly include: (1) in this kind of boiler, because of its design is based on atmospheric pressure, so, in the boiler the top of a hole communicating with the atmosphere. In addition, the boiler is run at atmospheric pressure, there is no risk of explosion, so that you can run to improve its safety factor of. (2) of the boiler, is the use of computer simulation to optimize the design, so the size thereof, may be made to optimize the design, thereby to make it look beautiful, and saving space. (3) If the fuel is a hot water boiler with full wet back three pass structure, then, it is the exhaust gas temperature can be effectively reduced, while increasing the heat transfer coefficient of the boiler. In addition, even with the boiler scale, then, easy to clean and cleanup.
4 tons of fuel boiler Product description: 4 tons of fuel oil boiler is heated by a burner, fuel atomization effect, fuel combustion, can not see the chimney smoke, so the green fuel boilers, energy efficient. After spraying fuel through the burner into the furnace in the atomized droplets, and easily mixed with air and the rapid combustion heat flash. Compared with coal-fired boiler with the same capacity, and parameters, which furnace volume heat intensity may be increased about twice. But to reduce the thermal load of the burner zone, in order to avoid overtemperature waterwall tubes in this area, so the furnace volume is only reduced by about 1/3. Because the ash content of fuel oil is small, without slagging in the convection heating surface, it allows the furnace exit gas temperatures as high as 1300 ~ 1350 ℃, and narrow a pitch between the convection heating surface to increase the flue gas velocity, thereby increasing the heat transfer coefficient of the heating surface, the heating area savings and steel. Features: 1, the boiler burner automatic combustion control in accordance with instructions, stop, separate control box has a number of security, performance, security and stability, low maintenance. 2, the inner fire tube inserted spoiler retardant, smoke slow speed, to strengthen the heat exchanger, combustion heat conducting large extent to the water, the low temperature flue gas discharged from the smoke chamber, reducing heat loss and save fuel. 3, the water level sensor water level real-time monitoring, to continuously monitor the water level is normal furnace. While controlling the temperature and replenishment level sensor solenoid valves, the boiler water may be continuously supplied. 4, centrifugal multi-layer insulation glass wool, steel for packaging famous white color, heat loss, anti-rust appearance. 5, the product is widely used in hospitals, schools, hotels, hotel, bath center and other enterprises. Boot check: 1, various instruments, whether the instrument to confirm the adequacy of fuel tank, and the inlet valve is opened. 2, confirm the soft capacity and the water tank boiler water quality meets the requirements of the main valve is opened and boiler feed water inlet valve. 3, rotation of the oil filter to remove debris. 4, drain the remaining water in the boiler, while the opening operation of the low level alarm and chain. Boiling furnace process: 1, before the new boiler furnace should be boiled to remove impurities and dirt inside the boiler, or trisodium phosphate soda cooking oven may be employed to prepare a 20% concentration was added furnace (not note the solid directly into the furnace). 2, after closing the steam valve and the water table Hancock, opening the vent valve according to the procedure stoker firing power may be low heat and temperature rise at the beginning, when there is moisture in the furnace, close the vent valve when the valve is discharged from the vent, the furnace pressure is raised to be at around 0.1MPa, the boiler should be checked for leakage and various accessories such as fittings, if any leakage should be promptly fastened. 3, when the pressure in the furnace reached 0.3MPa, the normal shutdown program shutdown, let the furnace pressure decreased to 0.1MPa or less, the drain valve open, give up all the water in the furnace. 4, opening into the hole, rinsed with soft water inside the boiler until the washing water coincides with the degree of acid-base soft water, after closing and opening into the hole Hancock water gauge. 5, after the completion of cooking stove washing, all restore normal operation, before normal operation stoker.
Based things, cloud computing, big data technology, fast Boiler actively exploring innovative operating mechanism boiler safety, independent research and development of the boiler cloud services on-line monitoring system. This system realizes the remote monitoring of the boiler, real-time understanding of boiler operation data and other functions to ensure the healthy operation of the boiler in the state, to achieve the lowest energy consumption and minimize emissions, safe and secure, which is equivalent to each boiler is equipped with a " private doctor".
A heated boiler is called a boiler. Heat transfer oil, also known as organic heat carrier or heat medium oil, has been used as intermediate heat transfer medium in industrial heat transfer for more than 50 years. Based on the idea of forced cycle design, a once-through boiler is developed. Generally, coal, oil and steam are used as fuel, heat conduction oil is used as the medium, hot oil circulation pump is used to force the medium into liquid phase circulation, heat energy is transmitted to the heating equipment and then returned to the heating furnace for re-heating. High operating temperature at low pressure, and high precision control for medium operation. The heat utilization rate of the system is high, and the transportation and maintenance are convenient. The closed circulation heat supply is connected with the atmosphere, can extend the service life of the boiler, liquid phase or gas phase transportation heating. The boiler adopts three-way coil design, the system sets the expansion water tank, and realizes low-pressure and high-temperature heating. The coil structure is adopted, the heating surface is sufficient, and the expansion is fully absorbed. Imported low-NOX combustion machine, combustion charge, belongs to environmental protection products. Boiler can choose advanced touch screen computer controller and digital computer controller automatic control system. With automatic temperature regulation, automatic ignition, and differential pressure, overtemperature, quenching protection. Boiler manufacturing standards, strictly in accordance with the relevant national standards. Pot The use of furnace water quality requirements: some users believe that as long as the boiler to maintain water can be, the water quality is not a choice. In fact, the quality of water on the boiler or have an impact, the editor recommends that you choose clean tap water. Because if there are impurities in the water, the use of this impurity water will have some impact on the equipment. The impurities form a thick layer of scale on the inner wall of the boiler. Scale will gradually thicken with time, and the accumulation of thickness will affect its heat transfer efficiency, resulting in a waste of energy consumption. If the scale appears, it should be cleaned up in time, so that the heat can be concentrated in the scale, which is not easy to emit. .