top laundry boiler steam generator for product wilford
Electric steam boiler electric steam boiler Notes Notes 1. Follow all warnings and instructions on the machine brands. 2. In order to prevent a negative pressure in the boiler, after sewage, before the next boiler operation, please do not close the drain valve. 3. In order to ensure the normal operation of the top laundry boiler steam generator for product wilford and security, should always observe the operation of the boiler pressure boiler, heating the water level and the situation is normal. When the steam generator failure, should immediately stop check, troubleshooting before the restart. 4. When the boiler stops longer running time, cut off the power while the boiler, the water inside the pipe exhausted to prevent frost damage, rusting. The machine usually is not used, power off, the control box is opened, check all the electrical device terminals fasteners, looseness should be sturdy, to prevent bad burning ignition wires have electrical device. 6. The electronic control box may not be water or steam and flammable gas, electric cabinet must shut the door in the boiler running. Never electrical control member any liquid or water flowing into the system, such as motors, electric control box. Cause gas boiler burner ignition misfire rod causes gas boiler burner ignition misfire bar: 1, the ignition bar gap interposed carbon residue with oil. 2, ignition rods fragmentation. moist. Leakage. 3, the distance between the ignition does not stick, too long or short. 4, ignition rods Insulation damage, short to ground. 5, ignition cable and transformer failure: cable, connector damage caused by a short circuit during ignition; transformer break or other fault occurs. Gas Burner fails, the action bar ignition misfire following five: Clear, renewal, adjust the distance, change and switching transformer.
Food factory steam boiler water shortages how food processing plant steam boiler water shortages how to deal with? Food factory steam boiler water shortages how to deal with? Steam boiler operators need to take what method to determine the boiler water, whether or not time to add water. When the steam boiler operators should find the boiler water do? When the top laundry boiler steam generator for product wilford water level drops below the minimum water level when the water level gauge can be directly color display all the color lights vapor. Low water level alarm number appears at high level and low level alarm. From this moment the low water level interlock, vehicle suspension. If the superheated steam temperature sharp rise performance, a steam outlet temperature higher than normal body. An exhaust gas temperature of the boiler increases. Small flow of water steam flow ratio. If a pipe rupture or economizer, should urgently add water.
Six months from Hainan Sinochem Pharmaceuticals boiler equipment normally used in odd years, the equipment in good condition, our technical staff has repeatedly went to inspect the guidance. In the process of Hainan with the pharmaceutical companies, the other either for my company's product or service we are very satisfied with our company's reputation and expressed trust. --customer feedback
1. The pressure test the electrical components of the electrical top laundry boiler steam generator for product wilford if the steam generator is completely assembled (i.e., as good as the boiler and the header connecting pipe, tube, heating the surface of the assembly line and the like). Header pressure test and assembly line can not, if they have been made in the component parts and hydraulic test or an ultrasound test of 100%, or other non-invasive test similar words. Upon completion of the processing of these components assembled, pressure is applied to test weld inspection no damage (radiation or ultrasound) to the full-length flaw detection. 2. All of the tubes, welded, cast, shaped parts and components, not all of the processing done in the hydrostatic test steel. Said component members of the hydrostatic test is not necessary, if they have done 100% ultrasonic testing or other similar NDT inspection. Superheater and economizer; while allowing the individual parts and components subjected to the hydraulic test in combination together with the electric boiler, not separate discrete electrical steam generator installation if reprocessing or hydrostatic test words. Included in the scope of the hydrostatic test all of the electrical steam generator, superheater, economizer, steam generation and processing power of the finished part. After working on the fixed plant boiler, is delivered to the sub-mounting parts, components, assemblies dispersion transportation, so the installation must be pressure test. Hydrostatic test purpose is to check electrical steam generator, superheater, economizer all density and strength member, all other members must also be welded hydrostatic test.